STINSON 108 C-FYMW   RESTORATION 

First I want credit a man whose blog has encouraged me to proceed with the restoration of a Stinson 108.  

 And that is of course that is  Randy Shields at Stinson  9598k restoration  blog. https://stinson9598k.blogspot.com/    I have read and re-read his blog many times since I first found it online. 

There are a number of others that are very helpful as well that I follow.  Thanks to all the bloggers who have put in the effort because  their knowledge and experience that is documented online will certainly help going forward in this project.  

I hope over  time my blog will be of help to someone rebuilding a Stinson  108 as well

The picture above is one of a stinson on floats I really like the looks of - especially the kids in the foreground - it must have been a wonderful summer for them.
As for the owner I am sorry for using the picture without permission. 
I am sure you won't mind.

• 
  

Hello to all that are following this blog.  This is my first attempt  at a blog so I am sure it will not be considered anywhere  close to professional 

My name is Murray Manning and I live in Kitchener Ontario Canada .

 I own  hangar at Waterloo Regional Airport  CYKF .

I  bought my first Stinson 108 in 2003 as a project and have collected a couple more air-frames along the way since then . They seem to be like stray dogs - I find them and bring them home. 

I have lots of Stinson parts and Franklin Engine parts but until now I have had no time to spend on the  projects.

My weekly schedule and workload has changed and I now have 4  days a week to devote to this project that I have  looked forward to for so many years.

It is my intention to build a airplane as close to original as possible with the addition of newer safety items like shoulder harness etc.

C-FYMW  Started its life as 108-655  known as a straight 108. In this rebuild we will be using most of the wings and tail units however I am replacing the fuselage with the one that came from N8500C  - a   108-1  That I purchased in Lockport N.Y  a few years ago. I decided to use this fuselage as it is a nice clean unit and it has a baggage compartment.  

The original fuselage from C-FYMW has some corrosion issues in the lower longerons  and I will use it in a home built project I have planned later - time permitting

  Hence I will be  rebuilding the aircraft to represent a 108-1. As a note of interest this aircraft was one of the limited number of 108's that were delivered from the factory in  the orange/yellow with a blue accent stripe paint scheme.

Below is a picture of  The original FYMW fuselage.I have it blasted and painted in epoxy to preserve but it needs some tubes replaced.

 

Below is a picture of N8500 when I acquired that air frame

This airplane had what was left of an original interior and original paint. The airplane as far as I can determine from it's logs was stored for many years in Upper Michigan

 I started to blast this fuse in my spare time in Nov - Dec 2020 and I got it blasted but not sprayed.  Pictures from my phone - not great clarity    

I ran out of good weather to spray the fuselage outside so I decided to create a spray booth in the hangar in the space under the mezzanine.

That took a few weeks to install the exhaust fan and build the walls.  

I can remove 4 screws and the panels on the right end come out to allow access to roll the fuse in and out.  

So the following photos are from the spray booth I created under the mezzanine in my hangar 

I Finally  had a few days together that I could deal with some oxidation on the fuse and hit it with  some 2 part epoxy primer. I used Stits EP420. It mixed up easy and sprayed well. I used a Hobbyair fresh air system (yellow box on the corner of the workbench) with a full facemask.  It works great and is a good investment as the expoxy and urethane paints with hardeners are nasty to the body. Here are some photos of the booth and the fuselage.

first coat of  Stits ep420 primer on YMW 's new fuselage